Cutting discs online supplier IE? Talking about the importance of soldering and welding is pointless if you already know about them. But, both of them have the drawback of emitting hazardous gases. Welding fumes contain considerable amounts of hydrogen fluoride gas, carbon monoxide, argon, and carbon dioxide. Also, the gases are known to contain manganese, beryllium, lead, aluminum, and arsenic. All of these can cause severe illnesses like cancer, kidney failure, and lead poisoning. So, is it wise to breathe in those poisonous fumes? Discover more info on https://www.weldingsuppliesdirect.ie/welding-equipment/mig-welders.htm.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

How to pick a welder tips: Fan on demand: Lowers running costs and reduces contamination to internal components. The fan kicks in when it’s needed, rather than running all day. Printed Circuit board protection: If the machine’s PCB’s are protected from dust & kept away from the fan, reliability will increase. Some manufacturers’ have the parts that need cooling in a duct type housing & the PCB isolated separately. Step voltage settings: If you’re looking at step voltage conventional MIG with multiple power settings – “the more the better!”

The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.

Some advices about welding equipment, MIG and TIG welders, plasma cutters. Stick Welding — If you learned to weld years ago, you likely learned using an arc welder. Stick welding for many years has been the most popular method for most home-shop welding needs. This process uses an electric current flowing from a gap between the metal and the welding stick, also known as an arc-welding electrode. Stick welding is an effective method for welding most alloys or joints and can be used indoors and outdoors or in drafty areas. It’s also the most economical welding method and provides the ability to create an effective bond on rusty or dirty metals. However, this method is limited to metals no thinner than 18-gauge, requires frequent rod changing, emits significant spatter and requires that welds be cleaned upon completion. Stick welding is also more difficult to learn and use, particularly the ability to strike and maintain an arc. Arc welders are available in AC, DC or AC/DC, with AC being the most economical. It’s used for welding thicker metals of 1/16 inch or greater. These machines are a good choice for farmers, hobbyists and home maintenance chores.

Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. See extra details on https://www.weldingsuppliesdirect.ie/.

Power tool pioneers Bosch have been in the game since 1886. They certainly know a thing or two about making one of the best corded angle grinders on the market. I was amazed at the power output and precision you can achieve with the GWS 7-115 angle grinder. Starting off with the look and feel of this grinder, it’s surprisingly slimline and lightweight. It’s certainly easy to hold on to and weighs less than 2 kg. Bosch have made use of a clever 20° angle side handle as well for ultimate precision grinding. Making use of one of Bosch’s brilliant 720 Watt Champion motors, you know this is a tool that’s built to last. Everything is chunky and built for hard work. They’ve included a two-stage safety switch to avoid accidental starts, which is essential for any tool like this. The motor spins a 115 mm cutting disc up to an impressive 11,000 rpm. There’s a relatively low amount of vibration when in use as well. Just 6.5 m/s², which isn’t bad at all for corded grinders. I like the fact that Bosch have flattened the gear head. This reduces the overall size and makes it easy to get into tight spots. If you’re looking for one of the best angle grinders from one of the top names in the business, this is a great choice.

If value for money is a priority to you, take a look at this drill from Evolution. It is a solid and durable drill that will get the job done for the professional steelworker as well as the weekend handyman. This drill has a 6-inch stroke length and comes with a 0.5-inch chuck and key. The drilling range has a diameter from 7/16? to 1-1/8? and cutting depth of 2 inches unless you change out the chuck to something else. You can place the feeding handle on either side of the drill, depending on what is comfortable to you. The heavy-duty magnet makes it easy to do overhead or horizontal drilling. An integrated cooling system will keep your magnetic drill press from overheating. There are some drawbacks to this drill. It can only turn at the speed of 570 RPM. This works great for when you are drilling steel or aluminum, but this speed is too high for drilling titanium or stainless steel. This drill may also be more primitive than conventional high-end magnetic drill presses.

The S SATC PCS Metal Cutting Disc for Angle Grinder is made with a proprietary aluminum oxide grain combination that creates an aggressive cutting action. This allows the user to cut through materials more easily. In addition, the wheel also has a balanced Cut Life, Cut Rate, Cut Precision, Power Demands & Heat Buildup. This means that you can cut through materials for longer periods of time without having to worry about the accuracy of the cut or the heat that is being generated. The SATC PCS Metal Cutting Discs will cut through most surfaces with ease and do not slow down as they work like other standard discs. These new discs also last much longer than other brands which allows you to make even more cuts before needing a replacement disc.

ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.

These welding tables are manufactured to the highest standards in Poland, Europe by GPPH. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. The hole system that these welding benches offer make precise construction a much quicker process when used in conjunction with the optional tool sets. Batch work processing times can be cut in half when you eliminate the measure and exact angle arrangement of individual parts – this makes producing the same item simple and fast.

The Lincoln EasyMIG 180 is a well-built welder that’s reliable and will serve a range of light fabrication and workshop projects. Its power input is 230V but it doesn’t have the power of the Hobart 190. This is a great entry level 230V welder that will give you quality welds. It won’t tackle thicker metal but this will do the job for most hobby welders. It’s a great choice for a hobbyist if you have a convenient 230V power outlet.

The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job.

UK market pick: LONGEVITY Inc is a company that has been around since only 2001. Like LOTOS Technology, it still produces a fine enough quality welder that it has earned its spot on this list. Besides the gas cylinder, this welder comes with everything you need to get started and is simple to set up. With all this, along with its solid performance, this machine is marked at a fair price of under $400. Though it is manufactured in China, the LONGEVITY Migweld is still a quality welder. It is most well-adapted to light use. Compared to Miller and Hobart’s machines, the price is somewhat better without sacrificing much quality. It welds from 24 gauge to ¼ inches of steel. Flux core is available for this welder. The LONGEVITY can run at ten different voltage settings. As an added bonus, it has thermal overload protection like the LOTOS welder.

Never drag, roll, or drop cylinders during the use. Always take care to maintain the valve caps during the transport. Avoid lifting the cylinder using a valve cap. Never store the cylinders for a long time period. Gas cylinders should only be purchased in small quantities. Never store them for long time periods. It is important to follow extreme precautions and safety measures while working with industrial gas cylinders due to several hazards and risks posed by them. Sourcing these cylinders from a reliable manufacturer is the most important safety measure for any facility owner using these cylinders.